Applied sciences

Archives of Electrical Engineering

Content

Archives of Electrical Engineering | 2012 | vol. 61 | No 4 December |

Abstract

In this paper, an analysis of the induction motor control scheme based on the Direct Rotor Flux Oriented Control (DRFOC) for a whole speed range, including fieldweakening (FW) regions is presented. Two field-weakening algorithms have been compared and verified through simulation with a 3.0 [kW] induction motor drive.

Go to article

Abstract

Some physical concepts important for a hysteresis model (effective field, anhysteretic magnetization) are discussed on the example of Jiles-Atherton model. The Jiles-Atherton model reveals some drawbacks, which make this model more difficult to be applied in electrical engineering. In particular, it does not describe accurately the magnetization curves after a reversal, moreover complex magnetization cycles are poorly represented. On the other hand, the phenomenological description proposed by Takács seems to be a valuable alternative to the Jiles-Atherton formalism. The concept of effective field may be easily incorporated in the description.

Go to article

Abstract

The calculation results of the static field parameters for permanent magnet linear synchronous motor have been presented in this work. The influence of the construction temperature on the parameters has been analyzed mathematically. Models for magnetic and temperature fields determination have been formulated. Two kinds of permanent magnets (NdFeB and SmCo) have been considered. The distribution of the thermal field has been obtained using the finite element method (FEM).

Go to article

Abstract

A study on plug-in electric vehicle (PEV) charging load and its impacts on distribution transformers loss-of-life, is presented in this paper. The assessment is based on residential PEV battery charging. As the exact forecasting of the charging load is not possible, the method for predicting the electric vehicle (EV) charging load is stochastically formulated. With the help of the stochastic model, the effect of fixed, time of use, and real-time charging rates on the charging load and the resultant impact on transformer derating is investigated. A 38-bus test system is adopted as the test system including industrial harmonic sources. Test results demonstrate that uncontrolled EV charging might causes a noticeable change in the K-factor of the transformer, emerging the need for derating, while applying real-time rates for battery charging loads conquers this problem even in case of harmonic-rich chargers.

Go to article

Abstract

This paper presents a simplified modeling, simulation and Experimental analysis of permanent magnet brushless dc motors (PMBLDC) for sensorless operation. This model provides a mechanism for monitoring and controlling of voltage, current, Speer and torque. The sensorless scheme employs direct back emf based zero crossing detection for controlling the dynamic characteristics.

Go to article

Abstract

This paper presents a new strategy for optimal placement of multi-type FACTS devices with a view to minimize losses besides enhancing the voltage profile using biogeography based optimization. The strategy places three types of FACTS devices that include static VAR compensator, thyristor controlled series compensator and unified power flow controller; and offers optimal locations for placement, type and parameters of the FACTS devices. Test results on IEEE 14, 30 and 57 bus systems reveal the superiority of the algorithm.

Go to article

Abstract

The paper presents a method for estimation of converter drive parameters. This estimation encompassed three types of drives, i.e. a static Scherbius drive, a driver with a brushless direct current (BLDC) motor and a drive with a voltage inverter. For drive modelling and parameter estimation, the author implemented original program mes written in FORTRAN. As well as these, the paper describes an objective function applied for the estimation. The author also compares gradient and gradientless methods, chich are applied for minimization of the objective function. Finally, the author explains the estimation results for example drives, focusing on the coincidence of theoretical and empirical waveforms. The abovementioned procedure led to the general rule, which facilitates estimation efficiency.

Go to article

Abstract

This paper presents optimization results for a two-phase, modular transverse flux switched reluctance motor (TFSRM) with an outer rotor. In particular, the main disadvantage of the considered motor structure, that is the zero starting torque in some rotor positions, is eliminated by construction optimization. A numerical model of the motor developed in the Flux3D program is coupled with a Matlab-based evolutionary algorithm for optimization of construction parameters of the magnetic circuit. The elaboratem algorithm is also connected with a database to limit the computation costs. Three objective functions are taken into account for the motor integral parameter improvement. The fundamental role of a type of an optimization criterion function is comparatively analyzed and a new effective criterion function is introduced.

Go to article

Abstract

Permanent magnet motors are more and more frequently used in various applications. In this group motors with a trapezoidal EMF deserve a special attention. They are characterized by a simple construction, high efficiency and high torque overload. A certain drawback of BLDC motors are difficulties with an operation at a speed above the nominal value. The article presents the results of investigations into the variablestructure electronic commutator designed for the drive of a small electric vehicle equipped with BLDC motors. Such a solution allows extending the standard range of the drive's speed. The considerations contained in the article focus on the possibilities and effects of regeneration mode in the proposed topology of converter. A theoretical analysis has been presented as well as computer simulations carried out by means of Matlab- Simulink, which were then verified at a laboratory. The tests were finished with trias conducted using a small electric vehicle Elipsa.

Go to article

Abstract

A numerical method is developed for estimation of temperature distributions inside tissues heated by external RF hyperthermia with external circular coil. The computational method relies on a solution of electromagnetic field problem in sinusoidal steadyt state. The heat transfer problem is treated in three dimensions with axis symmetry model. Than the bioheat diffusion equation under a steady-state condition is solved to determine the temperature distributions inside tumour and surrounding tissues. The heat removal due to the blood circulation is also taken into account. Numerical results are presented for heat generated by ferromagnetic nanoparticles in order to minimize negative effects of radiofrequency radiation.

Go to article

Abstract

The averaged models of switch-mode DC-DC power converters are discussed. Two methods of averaged model derivation are considered - the first, based on statespace averaging and the second, on the switch averaging approach. The simplest converters: BUCK, BOOST and BUCK-BOOST working in CCM (continuous conduction mode) or DCM are taken as examples in detailed considerations. Apart from the ideal converters, the more realistic case of converters with parasitic resistances is analyzed. The switch averaging approach is used more frequently than the other and is believed to be more convenient in practical applications. It is shown however, that in the deriving the averaged models based on the switch-averaging approach, some informalities have been made, which may be the source of errors in the case of converters with parasitic resistances, or working in DCM mode.

Go to article

Abstract

The separation of variables approach to formulate the averaged models of DC-DC switch-mode power converters is presented in the paper. The proposed method is applied to basic converters such as BUCK, BOOST and BUCK-BOOST. The ideal converters or converters with parasitic resistances, working in CCM and in DCM mode are considered. The models are presented in the form of equation systems for large signal, steady-state and small-signal case. It is shown, that the models obtained by separation of variables approach differ in some situations from standard models based on switch averaging method.

Go to article

Editorial office

Editor-in-Chief
Professor Andrzej Demenko, Poznan University of Technology, Poland

Deputy/ Managing Editor
Mariusz Barański, Ph.D., Poznan University of Technology, Poland
Łukasz Knypiński, Ph.D., Poznan University of Technology, Poland

Editorial Advisory Board
Chairman: Marian P. Kaźmierkowski, Warsaw, Poland
Secretary: Grzegorz Benysek, Zielona Gora, Poland

Members professors:
Antero Arkkio, Helsinki, Finland

Frede Blaabjerg,Aalborg, Denmark

Ion Boldea,Timisoara, Romania

Stanisław Bolkowski, Białystok, Poland

Herbert De Gersem,Darmstadt, Germany

Jacek Gieras, Rockford, USA

Kay Hameyer, Aachen, Germany

Mieczysław Hering,Warszawa, Poland

Marian K. Kazimierczuk, Dayton, USA

Stefan Kulig, Dortmund, Germany

David A. Lowther, Montreal, Canada

Jacek Marecki, Gdańsk, Poland

José Rodríguez Pérez,Valparaíso, Chile

Ryszard Sikora, Szczecin, Poland

Zbigniew Styczyński, Magdeburg, Germany

Jan Sykulski, Southampton, UK

 

Language Editor

Krystyna Guzek

Statistical Editor

Mariusz Barański, Poznan, Poland
Poznan University of Technology

Theme Editors

Mieczysław Hering, Warszawa, Poland
Professor at Warsaw University of Technology

Zbigniew Lubosny, Gdansk, Poland
Professor at Gdańnk University of Technology

Marian Łukaniszyn, Opole, Poland
Professor at Opole University of Technology

Marian Pasko, Gliwice, Poland
Professor at Silesian University of Technology

Stanisław Piróg, Krakow, Poland
Professor at AGH University of Science and Technology

Henryka Danuta Stryczewska, Lublin, Poland
Professor at Lublin University of Technology

Jan Sykulski, Southampton, UK
Professor at University of Southampton

Adam Szelag, Warsaw, Poland
Professor at Warsaw University of Technology

Romulad Włodek, Krakow, Poland
Professor at AGH University of Science and Technology

Technical Editor :

Typesetting in LATEX: Drukarnia Braci Grodzickich Sp.j., 05-500 Piaseczno, ul. Geodetów 47a, Poland

Contact

All contributions should be addressed to the Editor-in-Chief or the Editorial Office:

Address of the Editorial Office:

Archives of Electrical Engineering
Piotrowo 3A (Room 612X)
60-965 Poznan, Poland
tel: (48-61) 665-26-36
fax: (48-61) 665-23-81
e-mail: aee@put.poznan.pl

Website: www.aee.put.poznan.pl

Instructions for authors

ARCHIVES OF ELECTRICAL ENGINEERING (AEE) (previously Archiwum Elektrotechniki), quarterly journal of the Polish Academy of Sciences is OpenAccess, publishing original scientific articles and short communiques from all branches of Electrical Power Engineering exclusively in English. The main fields of interest are related to the theory & engineering of the components of an electrical power system: switching devices, arresters, reactors, conductors, etc. together with basic questions of their insulation, ampacity, switching capability etc.; electrical machines and transformers; modelling & calculation of circuits; electrical & magnetic fields problems; electromagnetic compatibility; control problems; power electronics; electrical power engineering; nondestructive testing & nondestructive evaluation.,

Journal Metrics:

Scoring assigned by the Polish Ministry of Science and Higher Education: 15 points

CiteScore metrics from Scopus, CiteScore 2018: 1.09

SCImago Journal Rank (SJR) 2018: 0.221

Source Normalized Impact per Paper (SNIP) 2018: 0.617

ICI Journal Master List 2017, Index Copernicus Value: 121.18

,

Manuscript submission:

All manuscripts should be submitted electronically on Editorial System.

Submission of paper to the Archives of Electrical Engineering is understood to imply that the article is original, unpublished and is not being considered for publication elsewhere. All articles will be reviewed. Since 2013, Authors wishing to use the facility of colour printing should consult the editors.,

Template:

Microsoft Word is recommended as a standard word processor to prepare the paper to the AEE journal. If you use the LaTex format, please transfer your document to Microsoft Word and then use Template AEE.
Please use Template AEE to prepare your paper. Template can be download from journal page - www.aee.put.poznan.pl,

The reviewing process:

Each paper submitted for publication in Archives of Electrical Engineering is subjected to the following review procedure:
a) the paper is reviewed by the editor in chief or guest editor for general suitability for publication in AEE
b) if it is judged suitable two reviewers are selected and a double blind peer review process takes place
c) based on the recommendations of the reviewers, the editor then decides whether the paper should be accepted in its present form, revised or rejected
d) the author(s) is(are) informed by e-mail on the results of the reviewing procedure.
The papers are published on average within 3 months after acceptance.,

Requirements for preparation of manuscripts:

The manuscripts submitted for publication should not exceed 21 000 characters (ca. 12 pages of a manuscript written on an A4 sheet in Times New Roman, 10pt font size, single line spacing and 3.8 cm margins). The manuscripts, written in UK English, should be typed using Template AEE according to the following instructions and should include: a title page with the title of a manuscript, a short title; abstract; key words, text; list of references. A DOI number as well as received and revised data will be completed by Editor. When you open Template.doc, select "Print Layout" from the "View" menu in the menu bar (View > Print Layout). Then type over sections of Template.doc or cut and paste from another document and then use markup styles (Home > Styles). For example, the style at this point in the document is "main text").
All papers submitted for publication are assessed on the basis of the mutual anonymity rule as to the names of reviewers and authors. Authors' names and affiliations should not appear in the attached text/tables/figures.
If English is not your first language, ask an English-speaking colleague to proofread your manuscript. The manuscripts that fail to meet basic standards of literacy are likely to be immediately declined or after the language assessment, sent to the authors for linguistic improvement.
The manuscripts are published on average within 3 months after their acceptance.
Do not change the font sizes or line spacing to squeeze more text into a limited number of pages. Leave some open space around your figures.,

Text:

The pages must be numbered consecutively. Articles should be divided into numbered sections, and if necessary subsections, preferably: Introduction, Material, Methods, Results, Conclusion and References. Any special characters (e.g. Greek, script, etc.) should be named in the margin where the character first occurs in the text. Names of species are to be accentuated with wavy underlining (italics). Equations should be numbered serially (1), (2), ... on the right side of the page. Footnotes should be avoided, if required, they should be used only for brief notes which do not fit well into the text. Figures and tables have to be included into the text. If table is typed on a separate page its position in the text should be marked. Abbreviations should be explained when they first appear in the text.,

Math:

Please use the Microsoft Equation 3.0 editor (comes with Microsoft Office 2007 and later versions) or the MathML editor as well as MathType editor to build an equation in your manuscript.
To insert an equation in Word, choose Insert, then Object. This will bring up a dropdown menu, where the Object option should be chosen again. Pressing it opens a popup window, where the Create New option has to be clicked. Scrolling down the window allows to find Microsoft Equation 3.0.

,

Equations:

Equations should be typed within the text, centred, and should be numbered consecutively throughout the text. Their numbers should be typed in parentheses, flush right. Equations should be referred to in text, e.g. (1), except at the beginning of a sentence: "Equation (1) is ...". All symbols appearing in equations have to be defined in the text, before or just after the equation.
If the symbols are written in Times New Roman use italic fonts. Symbols of vectors and matrices should be written in bold fonts. Do not italicize Greek fonts and mathematical symbols like e.g.: the derivative symbol d, max, min, etc. The indices of symbols that are indices themselves should be written in a clear manner.
Note that the equation is centered using a center tab stop. Please keep the same font in the formulas and text.,

Unit Symbols, Abbreviations:

Define abbreviations and acronyms the first time they are used in the text, even after they have been defined in the abstract. Abbreviations such as IEEE, SI, MKS, CGS, sc, dc, and rms do not have to be defined. Do not use abbreviations in the title or heads unless they are unavoidable.
Si units are recommended for use in formulas, drawings and tables., for example the SI unit for magnetic field strength H is A/m. Apply the center dot to separate compound units.
Do not mix complete spellings and abbreviations of units: "Wb/m2" or "webers per square meter," not "webers/m2." Spell units when they appear in text: "...a few henries…", not "...a few H…".
Use a zero before decimal points: "0.25," not ".25." Use "cm3," not "cc."
Unit Symbols, SI Prefixes as well as Abbreviations should be writing in accordance with the IEEE standard,

Tables, figures (illustrations) and captions:

The illustrations (line diagrams and photographs) should be suitable for direct reproduction. The lettering as well the details should have proportional dimensions to maintain their legibility after the usual reduction. All illustrations should be numbered consecutively (Fig. X). Tables are numbered with Arabic numerals.
All figures, figure captions, and tables in the text must be inserted into the correct places.
Figures, photos, tables or other parts of a manuscript that have previously appeared in another publication or are not the property of the authors must be properly acknowledged in the manuscript. Permission to republish these items must be obtained by the corresponding author from a person or institution holding the copyright, usually the publisher.
Authors are requested to send figures (diagrams, line drawings and photographic images) in separate computer files. JPG, PNG or TIF are the recommended file formats. Photographs, colour and greyscale figures should be at least at a resolution of 400dpi. Linear, including tables should be at a minimum of 600dpi.
All colour figures should be generated in the RGB or CMYK colour space, while greyscale images in the greyscale colour space.
When preparing your figures/graphics etc., we suggest the use of the Arial 8 point font for axis numbers and Arial 9 point font for axis names. Figures/graphics etc. can be prepared in one of two proposed ways - see Template AEE.
Tables are numbered with Arabic numerals. Use 9 point Times New Roman for the title of the table and 9 point Times New Roman for the filling of the table (9 in the case of symbols with subscripts).
AEE journal allows an author to publish color figures in e-version at no charge, and automatically convert them to grayscale for print versions. Authors wishing to use the facility of color printing should consult the editors.,

Conclusions:

A conclusion might elaborate on the importance of the work or suggest applications and extensions. Although a conclusion may review the main points of the manuscript, do not replicate the abstract as the conclusion.,

References:

References in text must be numbered consecutively by Arabic numerals placed in square brackets. Please make sure that you use full names of journals i.e. Archives of Electrical Engineering. Please ensure that all references in the Reference list are cited in the text and vice versa.
Please provide name(s) and initials of author(s), the title of the manuscript, editors (if any), the title of the journal or book, a volume number, the page range, and finally the year of publication in brackets.
You can use the rules presented on the site: IEEE standard

Examples of the ways in which references should be cited are given below:

Journal manuscript
[1] Author1 A., Author2 A., Title of paper, Title of periodical, vol. x, no. x, pp. xxx-xxx (YEAR).
example
[1] Steentjes S., von Pfingsten G., Hombitzer M., Hameyer K., Iron-loss model with consideration of minor loops applied to FE-simulations of electrical machines, IEEE Transactions on Magnetics. vol. 49, no. 7, pp. 3945-3948 (2013).
[2] Idziak P., Computer Investigation of Diagnostic Signals in Dynamic Torque of Damaged Induction Motor, Electrical Review (in Polish), to be published.
[3] Cardwell W., Finite element analysis of transient electromagnetic-thermal phenomena in a squirrel cage motor, submitted for publication in IEEE Transactions on Magnetics.

Conference manuscript
[4] Author A., Title of conference paper, Unabbreviated Name of Conf., City of Conf., Country of Conf., pp. xxx-xxx (YEAR).
example
[4] Popescu M., Staton D.A., Thermal aspects in power traction motors with permanent magnets, Proceedings of XXIII Symposium Electromagnetic Phenomena in Nonlinear Circuits, Pilsen, Czech Republic, pp. 35-36 (2016).

Book, book chapter and manual
[5] Author1 A., Author2 A.B., Title of book, Name of the publisher (YEAR).
example
[5] Zienkiewicz O., Taylor R.L., Finite Element method, McGraw-Hill Book Company (2000).

Patent
[6] Author1 A., Author2 A., Title of patent, European Patent, EP xxx xxx (YEAR).
example
[6] Piech Z., Szelag W., Elevator brake with magneto-rheological fluid, European Patent, EP 2 197 774 B1 (2011).

Thesis
[7] Author A., Title of thesis, PhD Thesis, Department, University, City of Univ. (YEAR).
example
[7] Driesen J., Coupled electromagnetic-thermal problems in electrical energy transducers, PhD Thesis, Faculty of Applied Science, K.U. Leuven, Leuven (2000).

For on electronic forms
[8] Author A., Title of article, in [Title of Conference, record as it appears on the copyright page], [copyright year] © [applicable copyright holder of the Conference Record]. doi: [DOI number].
example
[8] Kubo M., Yamamoto Y., Kondo T., Rajashekara K., Zhu B., Zero-sequence current suppression for open-end winding induction motor drive with resonant controller, in IEEE Applied Power Electronics Conference and Exposition (APEC), © APEC, 2016, doi: 10.1109/APEC.2016.7468259

Website
[9] http://www.aee.put.poznan.pl, accessed April 2010.,

Proofs:

Authors will receive proofs for correction, which should be returned promptly. All joint contributions must indicate the name and address of the authors to whom proofs should be sent.,

Fees for printing the papers in AEE:

AEE is published in Open Access, which means that all our articles on the Internet are available for readers free of charge, however it is requested that the authors pay an article-processing charge (reviewing, editing, proofreading, checking for plagiarism, distribution and so on) in order for their articles to be published and made freely available online immediately on publication.
The fee for the publication of an article in the AEE journal is 210 Euro.,

Abstracting & Indexing:

Archives of Electrical Engineering is covered by the following services:

  • Arianta
  • Baidu Scholar
  • BazTech
  • Celdes
  • CNKI Scholar (China National Knowledge Infrastucture)
  • CNPIEC
  • DOAJ
  • EBSCO - TOC Premier
  • EBSCO (relevant databases)
  • EBSCO Discovery Service
  • Elsevier - Compendex
  • Elsevier - Engineering Village
  • Elsevier - SCOPUS
  • Genamics JournalSeek
  • Google Scholar
  • ICI Journals Master List
  • Inspec
  • J-Gate
  • Naviga (Softweco)
  • POL-Index
  • Primo Central (ExLibris)
  • ProQuest - Advanced Technologies Database with Aerospace
  • ProQuest - Electronics and Communications Abstracts
  • ProQuest - Engineering Journals
  • ProQuest - High Tech Research Database
  • ProQuest - Illustrata: Technology
  • ProQuest - SciTech Journals
  • ProQuest - Technology Journals
  • ProQuest - Technology Research Database
  • SCImago (SJR)
  • Summon (Serials Solutions/ProQuest)
  • TDOne (TDNet)
  • TEMA Technik und Management
  • Thomson Reuters - Emerging Sources Citation Index
  • Ulrich's Periodicals Directory/ulrichsweb
  • WorldCat (OCLC)

Open Access policy

Archives of Electrical Engineering jest czasopismem wydawanym w wolnym dostępie na licencji CC BY-NC-ND 4.0.

Archives of Electrical Engineering is an open access journal with all content available with no charge in full text version. The journal content is available under the licencse CC BY-NC-ND 4.0.

This page uses 'cookies'. Learn more