Search results

Filters

  • Journals
  • Authors
  • Keywords
  • Date
  • Type

Search results

Number of results: 9
items per page: 25 50 75
Sort by:

Abstract

Porosity is one of the major defects in aluminum castings, which results is a decrease of a mechanical properties. Porosity in aluminum alloys is caused by solidification shrinkage and gas segregation. The final amount of porosity in aluminium castings is mostly influenced by several factors, as amount of hydrogen in molten aluminium alloy, cooling rate, melt temperature, mold material, or solidification interval. This article deals with effect of chemical composition on porosity in Al-Si aluminum alloys. For experiment was used Pure aluminum and four alloys: AlSi6Cu4, AlSi7Mg0, 3, AlSi9Cu1, AlSi10MgCu1.
Go to article

Abstract

Changes in the amount of basic nitrogen fractions (total, protein and non-protein nitrogen) were studied in an annual cycle. Significant seasonal changes were noted, minima occurring in Antarctic winter and maxima during spring-summer season. These changes are due mainly to high fluctuations of water content in krill in the annual cycle.
Go to article

Abstract

Physical and chemical properties of Arctic soils and especially the properties of surface horizons of the soils are very important because they are responsible for the rate and character of plant colonization, development of vegetation cover, and influence the rate and depth of thawing of soils and development of active layer of permafrost during summer. The main aim of the present study is to determine and explain the spatial diversity of selected physical and chemical properties of surface horizons of Arctic soils from the non-glaciated Fuglebekken catchment located in the Hornsund area (SW Spitsbergen) by means of geostatistical approach. Results indicate that soil surface horizons in the Fuglebekken catchment are characterized by highly variable physical and chemical properties due to a heterogeneous parent material (marine sediments, moraine, rock debris), tundra vegetation types, and non-uniform influence of seabirds. Soils experiencing the strongest influence of seabird guano have a lower pH than other soils. Soils developed on the lateral moraine of the Hansbreen glacier have the highest pH due to the presence of carbonates in the parent material and a lack or presence of a poorly developed and discontinuous A horizon. The soil surface horizons along the coast of the Hornsund exhibit the highest content of the sand fraction and SiO2. The surface of soils occurring at the foot of the slope of Ariekammen Ridge is characterized by the highest content of silt and clay fractions as well as Al2O3, Fe2O3, and K2O. Soils in the central part of the Fuglebekken catchment are depleted in CaO, MgO, and Na2O in comparison with soils in the other sampling sites, which indicates the highest rate of leaching in this part of the catchment.
Go to article

Abstract

The cement production process is associated with the emission of dust. These are mainly CKD (cement kiln dust) and BPD (by-pass dust), classified as wastes from group 10 – Wastes from thermal processes, subgroups 10 and 13 – wastes from manufacture of cement, lime and plaster and articles and products made from them. Cement kiln dust is a waste of variable composition and properties, which makes it a difficult material to recover. The main directions of recovery presented in the world literature indicate the use of dust from cement kilns in cement, mortar and concrete production, the production of bricks and in order to improve soil quality and wastewater treatment. Factors affecting chemical and phase compositions of dust from cement kilns are the reason why each waste should be analyzed individually. The paper presents the results of the analysis of the cement kiln dust after dedusting cement kilns and two bypass dusts. Analysis of the chemical composition has shown significant concentrations of chlorine, potassium and calcium in all wastes. The content of: Si, S, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, Zr, Pb, and Bi has also been confirmed. The analyzed dusts were characterized by the presence of carbonates (calcite, dolomite, and arcanite), quartz, alite, belite, sylvine, anhydrite, and portlandite in their phase composition. The leachates which were characterized by an alkaline reaction. In terms of leachability, high concentrations of chlorine ions in the analyzed dust leachates were confirmed, which significantly limits their use.
Go to article

Abstract

The aim of the studies was to evaluate the influence of sowing rate, foliar fertilization (Basfoliar fertilizer 6-12-6) and chemical composition on the mechanical properties of narrow- leaved lupine seeds of cultivars Bojar and Regent. Single seeds were burdened in the direction perpendicular to the parting plane of cotyledons with constant speed 10 mm∙min-1. The crop year and cultivar have significantly differentiated the value of all the analyzed strength parameters of narrow-leaved lupine seeds. The seeds of cultivar Bojar had significantly higher values of all the strength parameters. The designated strength parameters of lupine seeds were negatively correlated with ash content, fiber and protein except for the destructive force. They were also positively correlated with the fat content.
Go to article

Abstract

Blast furnace and cupola furnace are furnace aggregates used for pig iron and cast iron production. Both furnace aggregates work on very similar principles: they use coke as the fuel, charge goes from the top to down, the gases flow against it, etc. Their construction is very similar (cupola furnace is usually much smaller) and the structures of pig iron and cast iron are very similar too. Small differences between cast iron and pig iron are only in carbon and silicon content. The slags from blast furnace and cupola furnace are very similar in chemical composition, but blast furnace slag has a very widespread use in civil engineering, primarily in road construction, concrete and cement production, and in other industries, but the cupola furnace slag utilization is minimal. The contribution analyzes identical and different properties of both kinds of slags, and attempts to explain the differences in their uses. They are compared by the contribution of the blast furnace slag cooled in water and on air, and cupola furnace slag cooled on air and granulated in water. Their chemical composition, basicity, hydraulicity, melting temperature and surface were compared to explain the differences in their utilization.
Go to article

Abstract

The surface properties of particles emitted from six selected coal-fired power and heating plants in Poland have been studied in this work for the first time. Samples were collected beyond the control systems. Surface composition of the size-distributed particles was obtained by photoelectron spectroscopy (XPS). The reflection of the smallest, submicron particles was also measured to calculate their specific/mass absorption. The surface layer of the emitted particles was clearly dominated by oxygen, followed by silicon and carbon. The sum of the relative concentration of these elements was between 85.1% and 91.1% for coarse particles and 71.8–93.4% for fine/submicron particles. Aluminum was typically the fourth or fifth, or at least the sixth most common element. The mass absorption of the submicron particles emitted from the studied plants ranged from 0.02 m2g-1 to 0.03 m2g-1. Only specific absorption obtained for the “Nowy Wirek” heating plant was significantly higher than in other studied plants probably because the obsolete fire grate is used in this heating plant. The obtained results suggest that the power/heating-plant-emitted fine particles contain less carbonaceous material/elemental carbon on their surfaces than those that are typical in urban air.
Go to article

Abstract

Concentrations and elemental composition of fine (PM2.5) and coarse (PM2.5-10) ambient particles, at two sampling points located at the same urban background sites, were investigated. The points were 20 m distant from each other and at various heights (2 and 6 m) above the ground. A dichotomous sampler, equipped with a virtual impactor, and a cascade impactor were used to sample the dust. An X-ray fluorescence spectrometer was used in the elemental analyses. The investigations revealed heterogeneity of the spatial distribution and the elemental composition of suspended dust at the investigated urban background site. Coarse dust, whose concentration at 2.0 m above the ground was affected by secondary emission from roads, soil and other local low-level sources in some periods, appeared more heterogeneous.
Go to article

This page uses 'cookies'. Learn more